Nova Reader - Subject

Effect of spray-drying and ultraviolet C radiation as biosafety steps for CSFV and ASFV inactivation in porcine plasma

2021-04-28T00:00

Spray-dried animal plasma (SDAP) is widely used in diets of domestic animals to improve health status and increase growth and feed efficiency. Individual steps in the SDAP manufacturing process, including spray-drying, have been validated to inactivate potential pathogens. Manufacturing standards have established a minimum exit temperature of 80°C and a minimum post-drying storage period of 14 days at 20°C for production of SDAP. Also, UV-C irradiation has been evaluated as another inactivation step that could be included in the manufacturing process. The aim of this study was to assess the inactivation effectiveness of spray-drying on Classical swine fever virus (CSFV) and African swine fever virus (ASFV) and the effect of UV-C inactivation on ASFV as redundant biosafety steps of the manufacturing process for producing spray-dried porcine plasma (SDPP). This study demonstrated that UV-C treatment of liquid porcine plasma can inactivate more than 4 Log₁₀ TCID₅₀/mL of ASFV at 3000 J/L. Spray-drying effectively inactivated at least 4 Log₁₀ TCID₅₀/mL of both CSFV and ASFV. Incorporating UV-C technology within the SDAP manufacturing process can add another biosafety step to further enhance product safety.

ELISA detection of MPO-DNA complexes in human plasma is error-prone and yields limited information on neutrophil extracellular traps formed in vivo

2021-04-22T00:00

Over the past years, neutrophil extracellular traps (NETs) were shown to contribute to states of acute and chronic inflammatory disease. They are composed of expelled chromatin and decorated by neutrophil-derived proteins. Therefore, the analysis of DNA complexes with myeloperoxidase (MPO) by ELISA has become an attractive tool to measure NET formation in in vitro and in vivo samples. When we used a published MPO-DNA ELISA protocol and included an isotype control for the anti-MPO coating antibody, we observed high assay specificity for in vitro prepared NET samples, whereas the specificity for in vivo plasma samples was low. In addition, the assay failed to detect in vitro generated MPO-DNA complexes when spiked into plasma. Therefore, we set out to improve the specificity of the MPO-DNA ELISA for plasma samples. We found that the use of Fab fragments or immunoglobulins from different species or reversal of the antibody pair led to either a high background or a low dynamic range of detection that did not improve the specificity for plasma samples. Also, the use of higher plasma dilutions or pre-clearing of plasma immunoglobulins were ineffective. Finally, we found that a commercial reagent designed to block human anti-mouse antibodies and multivalent substances increased the detection window between the MPO antibody and isotype control for highly diluted plasma. We applied this modified ELISA protocol to analyze MPO-DNA complexes in human blood samples of acute and chronic inflammatory conditions. While markers of neutrophil activation and NET formation such as MPO, elastase and citrullinated histone H3 correlated significantly, we observed no correlation with the levels of MPO-DNA complexes. Therefore, we conclude that ELISA measurements of MPO-DNA complexes in human plasma are highly questionable regarding specificity of NET detection. In general, plasma analyses by ELISA should more frequently include isotype controls for antibodies to demonstrate target specificity.

Radon-220 diffusion from ²²⁴Ra-labeled calcium carbonate microparticles: Some implications for radiotherapeutic use

2021-03-04T00:00

Alpha-particle emitting radionuclides continue to be the subject of medical research because of their high energy and short range of action that facilitate effective cancer therapies. Radium-224 (²²⁴Ra) is one such candidate that has been considered for use in combating micrometastatic disease. In our prior studies, a suspension of ²²⁴Ra-labeled calcium carbonate (CaCO₃) microparticles was designed as a local therapy for disseminated cancers in the peritoneal cavity. The progenies of ²²⁴Ra, of which radon-220 (²²⁰Rn) is the first, together contribute three of the four alpha particles in the decay chain. The proximity of the progenies to the delivery site at the time of decay of the ²²⁴Ra-CaCO₃ microparticles can impact its therapeutic efficacy. In this study, we show that the diffusion of ²²⁰Rn was reduced in labeled CaCO₃ suspensions as compared with cationic ²²⁴Ra solutions, both in air and liquid volumes. Furthermore, free-floating lead-212 (²¹²Pb), which is generated from released ²²⁰Rn, had the potential to be re-adsorbed onto CaCO₃ microparticles. Under conditions mimicking an in vivo environment, more than 70% of the ²¹²Pb was adsorbed onto the CaCO₃ at microparticle concentrations above 1 mg/mL. Further, the diffusion of ²²⁰Rn seemed to occur whether the microparticles were labeled by the surface adsorption of ²²⁴Ra or if the ²²⁴Ra was incorporated into the bulk of the microparticles. The therapeutic benefit of differently labeled ²²⁴Ra-CaCO₃ microparticles after intraperitoneal administration was similar when examined in mice bearing intraperitoneal ovarian cancer xenografts. In conclusion, both the release of ²²⁰Rn and re-adsorption of ²¹²Pb are features that have implications for the radiotherapeutic use of ²²⁴Ra-labeled CaCO₃ microparticles. The release of ²²⁰Rn through diffusion may extend the effective range of alpha-particle dose deposition, and the re-adsorption of the longer lived ²¹²Pb onto the CaCO₃ microparticles may enhance the retention of this nuclide in the peritoneal cavity.

Association of periodontitis with oral malodor in Korean adults

2021-03-04T00:00

This study aimed to evaluate the association of periodontitis with the organoleptic score (OLS)-defined oral malodor after validating OLS with odoriferous sulfur compounds in mouth air among Korean adults. A total of 330 adults aged 47–86 years were recruited from the Yangpyeong health cohort, South Korea, in 2015. Oral malodor was assessed using a 6-point OLS by a trained dentist and validated with the concentrations of hydrogen sulfide (HS) and methyl mercaptan (MM) using a gas chromatographer. Periodontitis was measured by assessing the radiographic alveolar bone loss on digital orthopantomography. Statistical analyses including descriptive statistics, partial correlation, ANOVA, and multivariable logistic regression with putative confounders were applied. OLS was significantly correlated with the concentrations of HS and MM (partial r = 0.401 and 0.392, respectively; both p<0.001) after controlling for confounders. Individuals with periodontitis had 1.8 times the risk of OLS-defined oral malodor in multivariable models (adjusted odds ratio = 1.77 in the model with the number of teeth and 1.82 in the model with denture wearing; p = 0.047 and 0.035, respectively). Periodontitis was associated with OLS-defined oral malodor among Korean adults independent of known confounders. Periodontal conditions should be considered for clinical practice and research of oral malodor.

Transcriptome analysis of the role of autophagy in plant response to heat stress

2021-02-26T00:00

Autophagy plays a critical role in plant heat tolerance in part by targeting heat-induced nonnative proteins for degradation. Autophagy also regulates metabolism, signaling and other processes and it is less understood how the broad function of autophagy affects plant heat stress responses. To address this issue, we performed transcriptome profiling of Arabidopsis wild-type and autophagy-deficient atg5 mutant in response to heat stress. A large number of differentially expressed genes (DEGs) were identified between wild-type and atg5 mutant even under normal conditions. These DEGs are involved not only in metabolism, hormone signaling, stress responses but also in regulation of nucleotide processing and DNA repair. Intriguingly, we found that heat treatment resulted in more robust changes in gene expression in wild-type than in the atg5 mutant plants. The dampening effect of autophagy deficiency on heat-regulated gene expression was associated with already altered expression of many heat-regulated DEGs prior to heat stress in the atg5 mutant. Altered expression of a large number of genes involved in metabolism and signaling in the autophagy mutant prior to heat stress may affect plant response to heat stress. Furthermore, autophagy played a positive role in the expression of defense- and stress-related genes during the early stage of heat stress responses but had little effect on heat-induced expression of heat shock genes. Taken together, these results indicate that the broad role of autophagy in metabolism, cellular homeostasis and other processes can also potentially affect plant heat stress responses and heat tolerance.

Avidin-biotin complex-based capture coating platform for universal Influenza virus immobilization and characterization

2021-02-26T00:00

Influenza virus mutates quickly and unpredictably creating emerging pathogenic strains that are difficult to detect, diagnose, and characterize. Conventional tools to study and characterize virus, such as next generation sequencing, genome amplification (RT-PCR), and serological antibody testing, are not adequately suited to rapidly mutating pathogens like Influenza virus where the success of infection heavily depends on the phenotypic expression of surface glycoproteins. Bridging the gap between genome and pathogenic expression remains a challenge. Using sialic acid as a universal Influenza virus binding receptor, a novel virus avidin-biotin complex-based capture coating was developed and characterized that may be used to create future diagnostic and interrogation platforms for viable whole Influenza virus. First, fluorescent FITC probe studies were used to optimize coating component concentrations. Then atomic force microscopy (AFM) was used to profile the surface characteristics of the novel capture coating, acquire topographical imaging of Influenza particles immobilized by the coating, and calculate the capture efficiency of the coating (over 90%) for all four representative human Influenza virus strains tested.

Effects of a large-scale, natural sediment deposition event on plant cover in a Massachusetts salt marsh

2021-01-22T00:00

In mid-winter 2018, an unprecedented sediment deposition event occurred throughout portions of the Great Marsh in Massachusetts. Evaluation of this event in distinct marsh areas spanning three towns (Essex, Ipswich, and Newbury) revealed deposition covering 29.2 hectares with an average thickness of 30.1±2.1 mm measured shortly after deposition. While sediment deposition helps marshes survive sea level rise by building elevation, effects of such a large-scale deposition on New England marshes are unknown. This natural event provided an opportunity to study effects of large-scale sediment addition on plant cover and soil chemistry, with implications for marsh resilience. Sediment thickness did not differ significantly between winter and summer, indicating sediment is not eroding or compacting. The deposited sediment at each site had similar characteristics to that of the adjacent mudflat (e.g., texture, bivalve shells), suggesting that deposited materials resulted from ice rafting from adjacent flats, a natural phenomenon noted by other authors. Vegetative cover was significantly lower in plots with rafted sediment (75.6±2.3%) than sediment-free controls (93.1±1.6%) after one growing season. When sorted by sediment thickness categories, the low thickness level (1–19 mm) had significantly greater percent cover than medium (20–39 mm) and high (40–90 mm) categories. Given that sediment accretion in the Great Marsh was found to average 2.7 mm per year, the sediment thickness documented herein represents ~11 years of sediment accretion with only a 25% reduction in plant cover, suggesting this natural sediment event will likely increase long-term marsh resilience to sea level rise.

Single stranded DNA annealing is a conserved activity of telomere resolvases

2021-02-04T00:00

Bacterial species of the genera Agrobacterium and Borrelia possess chromosomes terminated by hairpin telomeres. Replication produces dimeric replication intermediates fused via replicated telomere junctions. A specialized class of enzymes, referred to as telomere resolvases, promotes the resolution of the replicated intermediate into linear monomers terminated by hairpin telomeres. Telomere resolution is catalyzed via DNA cleavage and rejoining events mechanistically similar to those promoted by topoisomerase-IB and tyrosine recombinase enzymes. Examination of the borrelial telomere resolvase, ResT, revealed unanticipated multifunctionality; aside from its expected telomere resolution activity ResT possessed a singled-stranded DNA (ssDNA) annealing activity that extended to both naked ssDNA and ssDNA complexed with its cognate single-stranded DNA binding protein (SSB). At present, the role this DNA annealing activity plays in vivo remains unknown. We have demonstrated here that single-stranded DNA annealing is also a conserved property of the agrobacterial telomere resolvase, TelA. This activity in TelA similarly extends to both naked ssDNA and ssDNA bound by its cognate SSB. TelA’s annealing activity was shown to stem from the N-terminal domain; removal of this domain abolished annealing without affecting telomere resolution. Further, independent expression of the N-terminal domain of TelA produced a functional annealing protein. We suggest that the apparent conservation of annealing activity in two telomere resolvases, from distantly related bacterial species, implies a role for this activity in hairpin telomere metabolism. Our demonstration of the separation of the telomere resolution and annealing activities of TelA provides a platform for future experiments aimed at identifying the role DNA annealing performs in vivo.

Application of a simulation model to the prognosis of material loss in wood processing

2021-02-02T00:00

The article discusses the influence of a sample size on the credibility of a simulation model created for the estimation of material loss in the production of a middle layer of a wooden floorboard. The study was conducted in a production company operating in the wood processing industry. Geometric characteristics of input material were captured and used to derive statistical distributions, which were then included in the simulation model. The conducted experiments indicated that the quality of the simulation model was significantly affected by the quality and quantity of the sample, on the basis of which the stochastic model is estimated. It was shown that small sample for wood processing data was insufficient to capture process variability. On the other hand, excessive sample size (80 or more observations) for the material with high natural geometric variability, involves taking into account outliers, which may lower the overall prognostic quality of the simulation model. Based on the conducted simulation experiments, the recommended sample size which allows development of a reliable model for estimation of material loss in the analyzed manufacturing process, ranges from 40 to 60 measurements.

Negligible-cost microfluidic device fabrication using 3D-printed interconnecting channel scaffolds

2021-02-03T00:00

This paper reports a novel, negligible-cost and open-source process for the rapid prototyping of complex microfluidic devices in polydimethylsiloxane (PDMS) using 3D-printed interconnecting microchannel scaffolds. These single-extrusion scaffolds are designed with interconnecting ends and used to quickly configure complex microfluidic systems before being embedded in PDMS to produce an imprint of the microfluidic configuration. The scaffolds are printed using common Material Extrusion (MEX) 3D printers and the limits, cost & reliability of the process are evaluated. The limits of standard MEX 3D-printing with off-the-shelf printer modifications is shown to achieve a minimum channel cross-section of 100×100 μm. The paper also lays out a protocol for the rapid fabrication of low-cost microfluidic channel moulds from the thermoplastic 3D-printed scaffolds, allowing the manufacture of customisable microfluidic systems without specialist equipment. The morphology of the resulting PDMS microchannels fabricated with the method are characterised and, when applied directly to glass, without plasma surface treatment, are shown to efficiently operate within the typical working pressures of commercial microfluidic devices. The technique is further validated through the demonstration of 2 common microfluidic devices; a fluid-mixer demonstrating the effective interconnecting scaffold design, and a microsphere droplet generator. The minimal cost of manufacture means that a 5000-piece physical library of mix-and-match channel scaffolds (100 μm scale) can be printed for ~$0.50 and made available to researchers and educators who lack access to appropriate technology. This simple yet innovative approach dramatically lowers the threshold for research and education into microfluidics and will make possible the rapid prototyping of point-of-care lab-on-a-chip diagnostic technology that is truly affordable the world over.

A comprehensive investigation of the reaction behaviorial features of coke with different CRIs in the simulated cohesive zone of a blast furnace

2021-01-11T00:00

The reaction characteristics and mechanism of coke with different coke reactivity indices (CRIs) in the high-temperature zone of a blast furnace should be fully understood to correctly evaluate the coke quality and optimize ironmaking. In this work, low-CRI coke (coke A) and high-CRI coke (coke B) were charged into a thermogravimetric analyzer to separately study their microstructural changes, gasification characteristics, and reaction mechanism under simulated cohesive zone conditions in a blast furnace. The results show that both coke A and coke B underwent pyrolysis, polycondensation, and graphitization during the heat treatment. The pyrolysis, polycondensation, gasification speed, and dissolution speed rates of coke B were higher than those of coke A. Direct and indirect reduction between sinter and coke occurred in the cohesive zone and had different stages. The consumption rate of coke B was faster than that of coke A during the coke–sinter reduction. The carbon molecules of coke A must absorb more energy to break away from the skeleton than those of coke B.

SiO_xN_y back-contact barriers for CZTSe thin-film solar cells

2021-01-12T00:00

The formation of molybdenum diselenide (MoSe₂) is widely observed at the back-contact interface for copper zinc tin selenide (CZTSe) thin-film solar cells. Depending on individual selenium (Se) supply and thermal conditions for forming CZTSe absorbers on molybdenum (Mo) substrates, the thickness of MoSe₂ can vary from a few hundreds of nanometers up to ≈ 1 μm, which is comparable to the commonly adopted thickness of 1 ~ 1.5 μm for CZTSe absorbers. In this study, for controlling the thickness of interfacial MoSe₂, thin diffusion barrier layers of silicon oxynitride (SiO_xN_y) are deposited onto Mo layers prior to the growth of CZTSe absorbers in the fabrication process. As a result, a reduction in the thicknesses of MoSe₂ layers is achieved. In terms of energy conversion efficiency (η), CZTSe solar cells grown on Mo/SiO_xN_y back contacts suffer a deterioration as the SiO_xN_y layers get thicker. CZTSe solar cells grown on Mo/SiO_xN_y/Mo back contacts preserve their efficiencies at ≈ 11% with thin 10 nm SiO_xN_y layers.

A study of evaluating specific tissue oxygen saturation values of gastrointestinal tumors by removing adherent substances in oxygen saturation imaging

2021-01-07T00:00

Objectives

Oxygen saturation (OS) imaging is a new method of endoscopic imaging that has clinical applications in oncology which can directly measure tissue oxygen saturation (Sto2) of the surface of gastrointestinal tract without any additional drugs or devices. This imaging technology is expected to contribute to research into cancer biology which leads to clinical benefit such as prediction to efficacy of chemotherapy or radiotherapy. However, adherent substances on tumors such as blood and white coating, pose a challenge for accurate measurements of the StO2 values in tumors. The aim of this study was to develop algorithms for discriminating between the tumors and their adherent substances, and to investigate whether it is possible to evaluate the tumor specific StO2 values excluding adherent substances during OS imaging.

Methods

We plotted areas of tumors and their adherent substances using white-light images of 50 upper digestive tumors: blood (68 plots); reddish tumor (83 plots); white coating (89 plots); and whitish tumor (79 plots). Scatter diagrams and discriminating algorithms using spectrum signal intensity values were constructed and verified using validation datasets. StO2 values were compared between the tumors and tumor adherent substances using OS images of gastrointestinal tumors.

Results

The discriminating algorithms and their accuracy rates (AR) were as follows: blood vs. reddish tumor: Y> - 4.90X+7.13 (AR: 95.9%) and white coating vs. whitish tumor: Y< -0.52X+0.17 (AR: 96.0%). The StO2 values (median, [range]) were as follows: blood, 79.3% [37.8%–100.0%]; reddish tumor, 74.5% [62.0%–86.9%]; white coating, 73.8% [42.1%–100.0%]; and whitish tumor, 65.7% [53.0%–76.3%].

Conclusions

OS imaging is strongly influenced by adherent substances for evaluating the specific StO2 value of tumors; therefore, it is important to eliminate the information of adherent substances for clinical application of OS imaging.

Fabrication and evaluation of complicated microstructures on cylindrical surface

2020-12-15T00:00

Various items of roll molds are popularly used to fabricate different kinds of optical films for optoelectronic information and other new and high-tech fields, while the fabrication and evaluation of optical microstructures on a cylindrical roller surface is more difficult than ecumenically manufactured products. In this study, the machinability of microstructures on the roll based on a fast tool servo (FTS) system is investigated. First, the flexible hinge holder for a FTS is designed and its structural parameters are optimized with finite-element analysis and fatigue reliability theory. The tool radius compensation algorithm for complicated microstructures is then deduced based on the surface fitting and bilinear interpolation algorithm of discrete data. Meanwhile, the evaluation index and method are proposed by the medium section method. Finally, a machining test of aspheric arrays on a cylindrical aluminum surface is carried out, and the high quality of the microstructure indicates that the proposed method is able to be used to fabricate optical microstructures.

3D printing direct to industrial roll-to-roll casting for fast prototyping of scalable microfluidic systems

2020-12-28T00:00

Microfluidic technologies have enormous potential to offer breakthrough solutions across a wide range of applications. However, the rate of scale-up and commercialization of these technologies has lagged significantly behind promising breakthrough developments in the lab, due at least in part to the problems presented by transitioning from benchtop fabrication methods to mass-manufacturing. In this work, we develop and validate a method to create functional microfluidic prototype devices using 3D printed masters in an industrial-scale roll-to-roll continuous casting process. There were no significant difference in mixing performance between the roll-to-roll cast devices and the PDMS controls in fluidic mixing tests. Furthermore, the casting process provided information on the suitability of the prototype microfluidic patterns for scale-up. This work represents an important step in the realization of high-volume prototyping and manufacturing of microfluidic patterns for use across a broad range of applications.

Computational analysis of the effects of geometric irregularities and post-processing steps on the mechanical behavior of additively manufactured 316L stainless steel stents

2020-12-29T00:00

Advances in additive manufacturing enable the production of tailored lattice structures and thus, in principle, coronary stents. This study investigates the effects of process-related irregularities, heat and surface treatment on the morphology, mechanical response, and expansion behavior of 316L stainless steel stents produced by laser powder bed fusion and provides a methodological approach for their numerical evaluation. A combined experimental and computational framework is used, based on both actual and computationally reconstructed laser powder bed fused stents. Process-related morphological deviations between the as-designed and actual laser powder bed fused stents were observed, resulting in a diameter increase by a factor of 2-2.6 for the stents without surface treatment and 1.3-2 for the electropolished stent compared to the as-designed stent. Thus, due to the increased geometrically induced stiffness, the laser powder bed fused stents in the as-built (7.11 ± 0.63 N) or the heat treated condition (5.87 ± 0.49 N) showed increased radial forces when compressed between two plates. After electropolishing, the heat treated stents exhibited radial forces (2.38 ± 0.23 N) comparable to conventional metallic stents. The laser powder bed fused stents were further affected by the size effect, resulting in a reduced yield strength by 41% in the as-built and by 59% in the heat treated condition compared to the bulk material obtained from tensile tests. The presented numerical approach was successful in predicting the macroscopic mechanical response of the stents under compression. During deformation, increased stiffness and local stress concentration were observed within the laser powder bed fused stents. Subsequent numerical expansion analysis of the derived stent models within a previously verified numerical model of stent expansion showed that electropolished and heat treated laser powder bed fused stents can exhibit comparable expansion behavior to conventional stents. The findings from this work motivate future experimental/numerical studies to quantify threshold values of critical geometric irregularities, which could be used to establish design guidelines for laser powder bed fused stents/lattice structures.

Poly(alizarin red S) modified glassy carbon electrode for square wave adsorptive stripping voltammetric determination of metronidazole in tablet formulation

2020-12-22T00:00

Potentiodynamically fabricated poly(alizarin red s) modified GCE was characterized using CV and EIS techniques. In contrast to the cyclic voltammetric response of the unmodified GCE for metronidazole, an irreversible reduction peak with three-folds of current enhancement and reduced overpotential at the poly(alizarin red s) modified GCE showed the catalytic effect of the modifier towards reduction of metronidazole. While observed peak potential shift with increasing pH (4.0–10.0) indicated the involvement of protons during the reduction of metronidazole, peak potential shift with scan rate (20–300 mV s^-1) confirmed the irreversibility of the reduction reaction of metronidazole at the modified GCE. A better correlation for the dependence of peak current on scan rate (r² = 0.9883) than on square root of scan rate (r² = 0.9740) supplemented by slope value of 0.38 for plot of log(current) versus log(scan rate) indicated the reduction reaction of metronidazole at the surface of the modified electrode was predominantly adsorption controlled. Under the optimized method and solution parameters, reductive current response of tablet sample showed linear dependence on spiked standard concentration in a wide range (0–125 μM) with excellent determination coefficient r², LoD and LoQ of 0.9991, 0.38, and 1.25 μM, respectively. Spike recovery of 97.9% and interference recovery of 96.2–97.5% in the presence of 21.28 and 31.92 μM of uric acid and ascorbic acid validated the applicability of the present method for determination of metronidazole in tablet formulation. The metronidazole content of the tested tablet formulation using standard addition method was found to be 97.6% of what is claimed by the tablet manufacturer making the developed method an excellent potential candidate for its applicability to determine metronidazole in real samples with complex matrix.

Climate Smart Agriculture

2017-10-19T18:30

The book uses an economic lens to identify the main features of climate-smart agriculture (CSA), its likely impact, and the challenges associated with its implementation. Drawing upon theory and concepts from agricultural development, institutional, and resource economics, this book expands and formalizes the conceptual foundations of CSA. Focusing on the adaptation/resilience dimension of CSA, the text embraces a mixture of conceptual analyses, including theory, empirical and policy analysis, and case studies, to look at adaptation and resilience through three possible avenues: ex-ante reduction of vulnerability, increasing adaptive capacity, and ex-post risk coping. The book is divided into three sections. The first section provides conceptual framing, giving an overview of the CSA concept and grounding it in core economic principles. The second section is devoted to a set of case studies illustratingthe economic basis of CSA in terms of reducing vulnerability, increasing adaptive capacity and ex-post risk coping. The final section addresses policy issues related to climate change. Providing information on this new and important field in an approachable way, this book helps make sense of CSA and fills intellectual and policy gaps by defining the concept and placing it within an economic decision-making framework. This book will be of interest to agricultural, environmental, and natural resource economists, development economists, and scholars of development studies, climate change, and agriculture. It will also appeal to policy-makers, development practitioners, and members of governmental and non-governmental organizations interested in agriculture, food security and climate change.